{"title":"End Bits \u0026 Corner Bits","description":"\u003ch2 dir=\"ltr\"\u003e\u003cspan\u003eWhy Blade Corners Wear Faster Than the Rest of the Blade\u003c\/span\u003e\u003c\/h2\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eMost maintenance attention on a dozer or grader blade goes to the cutting edge because it is the largest and most visible wear component on the assembly. End bits and corner bits at the extremities of the blade receive less systematic attention despite operating under a fundamentally more demanding load profile than the cutting edge face.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eThe reason is geometry. During a forward grading or push cycle, the cutting edge face moves through the material in a relatively uniform vector, distributing abrasive load across the full working width. The blade end, by contrast, presents a corner geometry to the material that concentrates lateral force, upward thrust from uneven terrain, and torsional stress at a single structural point. Every change in blade angle, every ground undulation the blade tip contacts, and every side-entry push cycle applies a compound force to the blade corner that the cutting edge centre never experiences.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eThe practical result is that end bits and corner bits wear at a rate that consistently exceeds the cutting edge wear rate per machine hour. Operators who replace cutting edges on schedule but defer end bit and corner bit replacement are allowing the highest-wear positions on the blade to operate unprotected, transferring wear directly to the structural blade steel at the points where repair is most difficult and most expensive.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch2 dir=\"ltr\"\u003e\u003cspan\u003eEnd Bits and Corner Bits: Understanding the Distinction\u003c\/span\u003e\u003c\/h2\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eThe terms end bit and corner bit are used interchangeably in the market, but they describe subtly different geometries that are not always directly substitutable on the same blade assembly.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch3 dir=\"ltr\"\u003e\u003cspan\u003eEnd Bits\u003c\/span\u003e\u003c\/h3\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eA dozer end bit, or blade end bit, is the bolt-on wear component fitted at each outer end of the dozer or grader blade, directly beside the cutting edge and extending past the blade face edge to protect the structural steel at the blade tip. The primary function is abrasion and impact protection at the blade extremity during push cycles and angled grading passes where the blade tip enters the material ahead of the centre face.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eEnd bits are manufactured with a profile that carries through from the cutting edge face, maintaining a consistent working geometry at the blade tip that supports clean material entry at the outer extremity. When the end bit is worn or absent, the structural blade tip carries the same load unprotected, and the wear progresses inward into the blade body rather than across a replaceable component face.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch3 dir=\"ltr\"\u003e\u003cspan\u003eCorner Bits\u003c\/span\u003e\u003c\/h3\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eA corner bit addresses the three-dimensional geometry at the blade corner where the cutting face, the back face, and the side of the blade converge. Where an end bit primarily protects the blade tip in the forward and lateral direction, a corner bit provides wrap-around protection at the junction of all three blade faces, addressing the torsional and multi-directional loading that occurs when the blade corner contacts material during angle changes, slope work, and cross-grading operations.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eGrader corner bits are particularly relevant on motor grader applications where blade angle and tilt are continuously varied through the work cycle, producing a rotating pattern of multi-directional corner loading that flat-face end bit geometry does not fully address. The Imara Engineering range carries both end bit and corner bit geometries, correctly distinguished and specified per machine and blade type.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch2 dir=\"ltr\"\u003e\u003cspan\u003eEnd Bits and Corner Bits in the Imara Engineering Range\u003c\/span\u003e\u003c\/h2\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eThe end bit and corner bit range at Imara Engineering is organised by machine type and application class, stocked in standard and heavy-duty structural grades with bolt-on configurations across all primary product families.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch3 dir=\"ltr\"\u003e\u003cspan\u003eDozer End Bits\u003c\/span\u003e\u003c\/h3\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eDozer blade end bit profiles in the Imara Engineering range cover Cat D-series dozers from the D4 through to the D9 class, with the Cat D6 and Cat D8 series end bit specifications representing the highest volume in the dozer segment of the catalogue. Cat end bits across the D-series programme are available in both standard and heavy-duty grades, with heavy-duty profiles specified for dozer operations in abrasive, rocky, or hard compacted ground where standard grade would reach wear limit at an uneconomical replacement interval.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eKomatsu end bits for the D51, D61, D65, and D85 dozer series are stocked and dimensionally cross-referenced per blade mounting configuration. The Komatsu D65 end bit specification is one of the most consistently ordered profiles in the Imara Engineering dozer range and is available for immediate dispatch in both standard and HD grades. Bolt-on end bits dozer configurations are stocked across the full Cat and Komatsu dozer range for operations requiring field replacement without blade removal.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch3 dir=\"ltr\"\u003e\u003cspan\u003eGrader End Bits and Corner Bits\u003c\/span\u003e\u003c\/h3\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eMotor grader end bit and corner bit profiles operate under the most varied loading conditions in the blade wear parts programme. Grading angle, material hardness, pass speed, and blade tilt all influence the wear pattern at the grader blade corner across a single production shift, which is why correct grader end bit specification matters more on motor grader applications than on the comparatively consistent load conditions of a dozer programme.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eThe Imara Engineering grader end bit range covers Cat, Komatsu, and John Deere motor grader configurations, with both grader end bit and grader corner bits available per blade mounting specification and model. Cat corner bits for the Cat 120, 140, and 160 motor grader series are stocked and cross-referenced to blade width and mounting bolt pattern. Komatsu corner bits for the GD655 and GD675 series are available alongside the broader Komatsu grader end bit programme. For road maintenance contractors running mixed grader fleets, the Imara Engineering range provides a single supply point for end bit replacement across multiple grader brands and blade configurations.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch3 dir=\"ltr\"\u003e\u003cspan\u003eHeavy-Duty Profiles for Severe Conditions\u003c\/span\u003e\u003c\/h3\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eHeavy-duty end bits and corner bits are the correct specification for operations where standard profiles wear below serviceable geometry faster than the replacement cycle allows. Applications that consistently demand heavy-duty end bit specification include:\u003c\/span\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli dir=\"ltr\" role=\"presentation\"\u003e\u003cspan\u003eDozer works in rocky or heavily compacted sub-base, where blade tip contact with rock faces and aggregate concentrations is a routine part of the push cycle\u003c\/span\u003e\u003c\/li\u003e\n\u003cli dir=\"ltr\" role=\"presentation\"\u003e\u003cspan\u003eGrader operations on unsealed roads with laterite, gravel, or crushed rock surfaces where the abrasive index is high, and blade angle variation is frequent\u003c\/span\u003e\u003c\/li\u003e\n\u003cli dir=\"ltr\" role=\"presentation\"\u003e\u003cspan\u003eBulk earthworks programmes where high production cycle rates mean the blade is in continuous contact with abrasive material across extended operating shifts\u003c\/span\u003e\u003c\/li\u003e\n\u003cli dir=\"ltr\" role=\"presentation\"\u003e\u003cspan\u003eRipping follow-up work where the dozer is working fractured material immediately behind a \u003ca href=\"https:\/\/imaraengineeringsupplies.com\/collections\/ripper-teeth-shanks?_pos=1\u0026amp;_psq=ripper\u0026amp;_ss=e\u0026amp;_v=1.0\"\u003e\u003cstrong\u003eripper \u003c\/strong\u003e\u003c\/a\u003epass, presenting angular aggregate to the blade tip on every push\u003c\/span\u003e\u003c\/li\u003e\n\u003cli dir=\"ltr\"\u003e\u003cspan\u003eImara Engineering heavy-duty end bits in these application classes are manufactured to an elevated hardness grade that extends service interval under the conditions above without sacrificing the toughness needed to absorb impact loading at the blade corner geometry.\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2 dir=\"ltr\"\u003e\u003cspan\u003eHow End Bit and Cutting Edge Replacement Interact\u003c\/span\u003e\u003c\/h2\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eEnd bit replacement and cutting-edge replacement are not independent maintenance events, and managing them as separate decisions rather than as a coordinated blade wear programme creates unnecessary cost at both replacement points.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eThe relationship works in both directions. When a cutting edge is replaced at the correct wear interval, the new edge presents a fresh, flat working face that transitions cleanly to the end bit geometry at the outer blade positions. If the end bits are significantly more worn than the cutting edge at that point, the junction between the new edge and the worn end bit creates a geometric discontinuity that produces an uneven working profile across the full blade width, affecting grade finish quality from the first pass with the new edge installed.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eThe reverse is equally true. Replacing end bits on a blade carrying a cutting edge that is approaching its wear limit creates the same discontinuity at the edge-to-end bit junction, and the new end bit geometry begins working against an uneven reference surface from day one.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eThe practical recommendation for fleet managers is to assess cutting edges and end bits together at every service inspection, and to coordinate replacement cycles so that both components are within the same wear band when either is scheduled for replacement. The Imara Engineering ground-engaging tools programme covers both cutting edges and end bits from a single supply point, simplifying that coordination for mixed dozer and grader fleets.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch2 dir=\"ltr\"\u003e\u003cspan\u003eMachine and Brand Compatibility\u003c\/span\u003e\u003c\/h2\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eEnd bits and corner bits in the Imara Engineering range are cross-referenced and stocked for the following brands and machine series:\u003c\/span\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli dir=\"ltr\" role=\"presentation\"\u003e\u003cspan\u003eCaterpillar (Cat): D4, D5, D6, D7, D8, D9 dozer series and Cat 120, 140, 160 motor grader range\u003c\/span\u003e\u003c\/li\u003e\n\u003cli dir=\"ltr\" role=\"presentation\"\u003e\u003cspan\u003eKomatsu: D51, D61, D65, D85 dozer series and GD655, GD675 motor grader range\u003c\/span\u003e\u003c\/li\u003e\n\u003cli dir=\"ltr\" role=\"presentation\"\u003e\u003cspan\u003eJohn Deere: 700 and 800 series dozers and 670 and 770 motor grader range\u003c\/span\u003e\u003c\/li\u003e\n\u003cli dir=\"ltr\" role=\"presentation\"\u003e\u003cspan\u003eVolvo: A-series and G-series grader range\u003c\/span\u003e\u003c\/li\u003e\n\u003cli dir=\"ltr\" role=\"presentation\"\u003e\u003cspan\u003eCase: 1650M and 2050M dozer series\u003c\/span\u003e\u003c\/li\u003e\n\u003cli dir=\"ltr\" role=\"presentation\"\u003e\u003cspan\u003eChampion: motor grader range\u003c\/span\u003e\u003c\/li\u003e\n\u003cli dir=\"ltr\" role=\"presentation\"\u003e\u003cspan\u003eNew Holland: dozer and grader configurations\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eFor machine models or blade configurations not listed, end bit and corner bit specifications can be cross-referenced from blade width, bolt hole pattern, mounting hole spacing, and section thickness provided by the buyer.\u003c\/span\u003e\u003cspan\u003e\u003c\/span\u003e\u003c\/p\u003e","products":[{"product_id":"195-71-61930-cutting-edge-end-bit-for-komatsu-d475","title":"Cutting Edge \u0026 End Bit Blade 195-71-61930 for Komatsu D475 Dozer","description":"\u003cp data-start=\"75\" data-end=\"118\"\u003e\u003cstrong data-start=\"75\" data-end=\"89\"\u003ePart Name:\u003c\/strong\u003e Cutting Edge \u0026amp; End Bit Blade\u003c\/p\u003e\n\u003cp data-start=\"120\" data-end=\"152\"\u003e\u003cstrong data-start=\"120\" data-end=\"139\"\u003ePart Number(s):\u003c\/strong\u003e 195-71-61930\u003c\/p\u003e\n\u003cp data-start=\"154\" data-end=\"268\"\u003e\u003cstrong data-start=\"154\" data-end=\"185\"\u003eApplication\/ Compatibility:\u003c\/strong\u003e Komatsu D475 Dozers – fits the main cutting edge and corner positions on the blade\u003c\/p\u003e\n\u003cp data-start=\"270\" data-end=\"415\"\u003e\u003cstrong data-start=\"270\" data-end=\"283\"\u003eFunction:\u003c\/strong\u003e Provides a durable, wear-resistant edge for dozing, leveling, and ground-cutting operations; protects the blade structure from wear\u003c\/p\u003e\n\u003cp data-start=\"417\" data-end=\"468\"\u003e\u003cstrong data-start=\"417\" data-end=\"431\"\u003eCondition:\u003c\/strong\u003e Brand New \/ OEM Standard Replacement\u003c\/p\u003e\n\u003cp data-start=\"470\" data-end=\"497\"\u003e\u003cstrong data-start=\"470\" data-end=\"487\"\u003eMachine Type:\u003c\/strong\u003e Bulldozer\u003c\/p\u003e\n\u003cp data-start=\"499\" data-end=\"528\"\u003e\u003cstrong data-start=\"499\" data-end=\"528\"\u003eTechnical Specifications:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp data-start=\"530\" data-end=\"585\"\u003e\u003cstrong data-start=\"530\" data-end=\"539\"\u003eType:\u003c\/strong\u003e Weld-on\/bolt-on cutting edge and corner blade\u003c\/p\u003e\n\u003cp data-start=\"587\" data-end=\"638\"\u003e\u003cstrong data-start=\"587\" data-end=\"600\"\u003eMaterial:\u003c\/strong\u003e Heat-treated, high-carbon steel alloy\u003c\/p\u003e\n\u003cp data-start=\"640\" data-end=\"687\"\u003e\u003cstrong data-start=\"640\" data-end=\"651\"\u003eLength:\u003c\/strong\u003e OEM standard length for D475 blades\u003c\/p\u003e\n\u003cp data-start=\"689\" data-end=\"755\"\u003e\u003cstrong data-start=\"689\" data-end=\"703\"\u003eThickness:\u003c\/strong\u003e Designed to match Komatsu D475 blade specifications\u003c\/p\u003e\n\u003cp data-start=\"757\" data-end=\"804\"\u003e\u003cstrong data-start=\"757\" data-end=\"770\"\u003eHardness:\u003c\/strong\u003e 450–500 HB for extended wear life\u003c\/p\u003e\n\u003cp data-start=\"806\" data-end=\"860\"\u003e\u003cstrong data-start=\"806\" data-end=\"823\"\u003eInstallation:\u003c\/strong\u003e Direct fitment with OEM bolt pattern\u003c\/p\u003e\n\u003cp data-start=\"862\" data-end=\"901\"\u003e\u003cstrong data-start=\"862\" data-end=\"873\"\u003eWeight:\u003c\/strong\u003e Approx. 95–110 kg per piece\u003c\/p\u003e\n\u003cp data-start=\"903\" data-end=\"944\"\u003e\u003cstrong data-start=\"903\" data-end=\"916\"\u003eCategory:\u003c\/strong\u003e Ground Engaging Tools (GET)\u003c\/p\u003e\n\u003cp data-start=\"946\" data-end=\"1008\"\u003e\u003cstrong data-start=\"946\" data-end=\"959\"\u003eShipping:\u003c\/strong\u003e Global Shipping Available | Delivery in 3-5 Days\u003c\/p\u003e","brand":"Imara Engineering Supplies","offers":[{"title":"Default Title","offer_id":43660186255560,"sku":"1600437240086","price":150.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0600\/5348\/7816\/files\/H5e9b7f4fed064e52b556feae82339ac2O.webp?v=1716317018"}],"url":"https:\/\/imaraengineeringsupplies.com\/en-ca\/collections\/end-bits-corner-bits.oembed","provider":"Imara Engineering Supplies","version":"1.0","type":"link"}